Electronics Forum | Fri Jul 04 21:09:04 EDT 2003 | ramanandkini
I have a CEM-1 PCB board with 35 microns copper. This is PCB is finished with SMOBC+HALS. We do solder SMT LEDs, but till date we do not have problems that you have listed. The LEDs are good & bright. It even passed high & low temp cycle tests (-40 t
Electronics Forum | Mon Jul 19 14:58:50 EDT 2004 | mattkehoe
We have a need for expert opinions on a solderability issue. Our company prints and then reflows solder paste with no components in place. It is then washed and flattened with a special flattening machine. Usually, the paste fuses and spreads out
Electronics Forum | Thu Jan 14 04:41:29 EST 2016 | saimen
Hi There , Glad to contact with you , Here is Saimen in Tianweisheng , wish we will have a good cooperation in the furture if we have the honor . Our company is one of the largest custom-made PCB manufacturer in China. We can OEM,ODM,EMS single side
Electronics Forum | Thu Apr 27 10:35:21 EDT 2000 | Russ
Scott, I am a little confused, when you mention "silver thru hole vs. plated through hole what do you mean. A silver "immersion" type finish vs. HASL (Tin lead)on your PCB? Or are you talking about using silver solder to perform intrusive reflow of
Electronics Forum | Fri Jun 08 17:22:51 EDT 2007 | naynayno
We have been producing an IMS assembly with SMT dpak's for some time. However, we recently encountered a new problem by chance - the parts can be flicked off with a finger nail. I state by chance because the solder joints are wetted and shiny with
Electronics Forum | Fri Apr 30 10:56:27 EDT 2004 | Bryan She
We tested J6 open on .5mm pitch CSP(In fact,only resistance much lower than normal).J6 is one of the corner ball of the CSP.Defect rate is about 3%. Stencil:4 mil thickness,10 mil square aperture, solder mask openning:10 mil diameter circle. Board fi
Electronics Forum | Tue Oct 03 18:41:16 EDT 2006 | C.K. Flip
With recent implementation of VOC-Free flux in our shop, we've experienced little solder fines/balls on the above combo of VOC-Free, Water Based, and glossy to semi-glossy mask finish on PCB's. The solder balls show up on close conductor spacings, ~
Electronics Forum | Thu Apr 12 09:50:51 EDT 2007 | pjc
There have been many designs of apertures for 0402, round, home plate, inverted home plate and various reduction amounts for square or rectangular apertures. What works best for a given application depends on PCB design, solder land finish, stencil t
Electronics Forum | Thu Jun 21 16:30:47 EDT 2012 | grauen06
We are currently using an ACE K.I.S.S. 104. We used SN100 solder with AIM NC265 flux (no clean, alcohol-based). Also, we use topside preheat at 100 degrees C and a 6mm nozzle (as big as we can go with this application). The PCB has a matte finish as
Electronics Forum | Fri Jan 15 11:28:50 EST 1999 | Bob Willis
| | Folk's, | | | | I'm looking for information of how long you cna store a gold finish PCB before building it. I know there are problems with the gold disappearing into the underlying nickle over time / temperature etc but exactly how long do you h
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
